Description
Add clear background music and paging to restaurants, retail stores, offices and other commercial spaces with a compact wall-mounted speaker designed for flexible sound coverage.
The TEXONIC CS75 is a 5.25-inch two-way commercial wall speaker with selectable 70V and 100V transformer taps plus an 8-ohm operating mode. Its adjustable mounting bracket allows the speaker to be installed vertically or horizontally and aimed toward customer, seating, work or listening areas. It is a practical solution for indoor and protected covered-outdoor applications where ceiling speakers are not suitable.
TEXONIC CS75 Commercial Wall Speaker
The CS75 combines a compact ABS enclosure, metal grille, two-way driver system, built-in commercial audio transformer and adjustable stainless-steel bracket in one surface-mount speaker.
It is designed for commercial background music, paging and general voice announcements in spaces where cutting ceiling openings is not practical or where directional wall-mounted sound is preferred.
Brand: TEXONIC
Model: CS75
Speaker type: 5.25-inch two-way commercial wall speaker
System compatibility: 70V, 100V or 8Ω
Selling unit: One speaker with mounting bracket
Two-Way Sound for Music and Paging
A 5-inch driver reproduces lower and middle frequencies while a separate 1-inch dome tweeter handles higher-frequency detail.
The two-way design provides more balanced music reproduction and clearer voice detail than a basic single-cone paging speaker. It is suitable for businesses that use the same speaker system for everyday background music and occasional announcements.
Clear Commercial Background Music
The CS75 has a published frequency response of 60Hz–20kHz at -10dB, supporting vocals, instruments, paging and general business audio.
It is well suited to comfortable background music and clear voice reproduction. For deep bass, high-volume foreground music or demanding entertainment applications, consider adding a commercial subwoofer or selecting a larger high-output speaker system.
Wide 120° Sound Coverage
The published 120-degree coverage helps distribute music and speech across a broad listening area from each wall or open-ceiling location.
The adjustable bracket also allows each speaker to be aimed toward customer areas, tables, reception desks, hallways, workspaces or other occupied sections of the room.
Recommended Commercial Applications
| Business Type | Typical Use |
|---|---|
| Restaurant or Café | Dining-room music, patio audio and staff announcements |
| Retail Store or Showroom | Customer-facing music, paging and promotional messages |
| Office or Reception Area | Background music, general paging and presentation audio |
| Hotel or Hospitality Space | Lobby, lounge, corridor, meeting-room and breakfast-area audio |
| Salon, Spa or Clinic | Comfortable ambient music and clear general announcements |
| School or Training Facility | Classroom audio, program sound and voice paging |
| Open-Ceiling Business | Surface-mounted audio where recessed speakers are impractical |
70V and 100V Distributed Audio Compatibility
The transformer built into the CS75 allows multiple speakers to connect to a compatible 70V or 100V commercial amplifier.
Constant-voltage systems are useful when several speakers must operate over longer cable runs. The speakers connect electrically in parallel, and the selected transformer taps are added together to calculate the total amplifier load.
Selectable Transformer Taps
| Speaker-Line Voltage | Available Tap Settings |
|---|---|
| 70V | 1.9W / 3.75W / 7.5W / 15W / 30W |
| 100V | 3.75W / 7.5W / 15W / 30W |
| Low Impedance | 8Ω mode |
Select the tap value that matches the amplifier’s speaker-line voltage.
Do not use the 1.9W setting with a 100V amplifier. The lowest published tap at 100V is 3.75W.
Choosing the Right Tap Setting
| Tap Range | General Application |
|---|---|
| 1.9W–3.75W | Quiet offices, hallways and low-level ambient sound |
| 7.5W | General office, retail and hospitality background music |
| 15W | Restaurants, showrooms and areas with moderate background noise |
| 30W | Larger or noisier areas requiring stronger speaker output |
These are general planning examples. Final tap selection depends on speaker quantity, room dimensions, mounting height, background noise, listening distance and the required sound level.
Speaker Load and Amplifier Examples
Add the transformer tap of every speaker connected to the same commercial amplifier. Maintain practical reserve capacity rather than loading the amplifier to its full rated output.
| Speaker Configuration | Total Load | Practical Amplifier Size |
|---|---|---|
| 3 speakers at 15W | 45W | 60W or higher |
| 4 speakers at 15W | 60W | 120W or higher |
| 6 speakers at 15W | 90W | 120W or higher |
| 8 speakers at 15W | 120W | 240W or higher |
| 4 speakers at 30W | 120W | 240W or higher |
| 8 speakers at 30W | 240W | 350W or higher |
Example: Six speakers set to 15W create a total load of 90W.
A 120W commercial amplifier allows 30W of unused capacity for normal operating reserve.
Different Tap Settings in One System
CS75 speakers connected to the same 70V or 100V line can use different transformer taps.
For example, speakers in a quiet hallway may use 3.75W while speakers in a busy customer area use 15W. Add every selected tap separately when calculating the final amplifier load.
8Ω Low-Impedance Operation
The rear selector also provides an 8-ohm operating position for use with a compatible low-impedance amplifier.
The speaker is rated for up to 80W in 8Ω mode. One speaker presents an 8-ohm nominal load. Two speakers connected in parallel create a 4-ohm load, which should be used only with an amplifier that supports 4Ω operation.
Never connect the speaker to a 70V or 100V output while the selector is set to 8Ω. Low-impedance and constant-voltage calculations are different and must not be mixed.
Parallel and Daisy-Chain Wiring
In a 70V or 100V system, multiple speakers connect electrically in parallel. The cable may physically run from the amplifier to the first speaker and continue to the remaining speakers.
- Connect every speaker to the same 70V or 100V speaker line.
- Keep positive and common polarity consistent throughout the run.
- Select the correct transformer tap on every speaker.
- Add all selected tap values when calculating the total load.
- Use speaker cable approved for the building and installation area.
- Switch off the amplifier before wiring or changing tap settings.
Important Connection Warning
Select the correct 70V, 100V or 8Ω operating mode before switching on the amplifier.
Do not connect a speaker set for 70V operation to a 100V output.
Do not connect a speaker set for 8Ω operation to a constant-voltage output.
Do not connect 70V, 100V and low-impedance outputs to the same speaker line.
Power down and disconnect the amplifier before wiring speakers or changing transformer settings.
Flexible Wall and Open-Ceiling Installation
The included U-shaped bracket allows the CS75 to be mounted on a wall, column or suitable open-ceiling structure.
The enclosure may be installed vertically or horizontally and then angled toward the intended listening area. This provides more control over sound direction than a fixed flush-mounted ceiling speaker.
Indoor and Protected Covered-Outdoor Use
The CS75 is suitable for indoor installations and protected covered-outdoor areas such as roofed patios or entrances where the speaker is sheltered from direct weather exposure.
The published specifications do not list an IP weather rating. Do not install the speaker where it will be directly exposed to rain, snow, water spray, standing moisture or severe weather.
Durable Commercial Construction
- Durable ABS speaker enclosure
- Protective metal front grille
- Stainless-steel U-shaped mounting bracket
- Rear transformer-tap selector
- Horizontal or vertical mounting
- Adjustable listening angle
Installation Planning
- Confirm that the wall or structure can support the 2.3kg speaker and bracket.
- Use screws, bolts or anchors rated for the mounting surface.
- Check for electrical wiring, plumbing and HVAC components before drilling.
- Aim speakers toward occupied areas rather than reflective walls or glass.
- Distribute multiple speakers evenly instead of placing them in one area.
- Follow applicable building, electrical and installation requirements.
Surface-specific screws, bolts and wall anchors are not included. Select mounting hardware according to the wall material, structure and installation requirements.
Technical Specifications
| Brand | TEXONIC |
| Model / SKU | CS75 |
| Product Type | Two-way commercial wall and surface-mount speaker |
| Nominal Speaker Size | 5.25 inches |
| Low-Frequency Driver | 5-inch driver |
| High-Frequency Driver | 1-inch dome tweeter |
| Speaker-Line Compatibility | 70V / 100V distributed audio |
| 70V Transformer Taps | 1.9W / 3.75W / 7.5W / 15W / 30W |
| 100V Transformer Taps | 3.75W / 7.5W / 15W / 30W |
| Transformer Impedance | 2.6kΩ / 1.3kΩ / 670Ω / 330Ω / 165Ω |
| Low-Impedance Mode | 8Ω |
| Rated Power in 8Ω Mode | 80W |
| Frequency Response | 60Hz–20kHz at -10dB |
| Sensitivity | 92dB at 1W / 1m |
| Published Coverage | 120° |
| Enclosure | ABS cabinet |
| Grille | Metal grille |
| Mounting Bracket | Adjustable stainless-steel U-shaped bracket |
| Mounting Orientation | Horizontal or vertical |
| Dimensions | 24.3 × 18.5 × 18.6cm |
| Weight | 2.3kg / approximately 5.1 lb |
| Recommended Environment | Indoor or protected covered-outdoor installation |
| UPC / GTIN | 608597857337 |
| Recommended Use | Commercial background music, paging and announcements |
What’s Included
- 1 × TEXONIC CS75 commercial wall speaker
- 1 × Adjustable U-shaped wall-mount bracket
- CS75 user-manual access
Warranty
TEXONIC CS75: Three-year manufacturer’s warranty, subject to the current TEXONIC warranty terms and proof of purchase.
Frequently Asked Questions
Is the CS75 sold individually or as a pair?
The CS75 is sold individually. Each product unit includes one speaker and one adjustable mounting bracket.
Can the CS75 connect to a 70V amplifier?
Yes. The available 70V taps are 1.9W, 3.75W, 7.5W, 15W and 30W. Add the selected tap of every connected speaker when calculating the amplifier load.
Can it connect to a 100V amplifier?
Yes. The available 100V taps are 3.75W, 7.5W, 15W and 30W. Select only a tap identified for 100V operation.
Can it connect to a regular 8-ohm amplifier?
Yes. Set the rear selector to 8Ω and confirm that the complete speaker load remains compatible with the amplifier.
How many CS75 speakers can connect to one amplifier?
The quantity depends on the amplifier rating and selected transformer taps. Add the wattage setting of every speaker and leave practical amplifier reserve capacity.
Is the CS75 suitable for music and paging?
Yes. Its two-way driver design is suitable for commercial background music, clear speech and general paging announcements.
Can the speaker be mounted horizontally?
Yes. The U-shaped bracket supports horizontal or vertical installation and allows the speaker angle to be adjusted.
Can the CS75 be used outdoors?
It may be used in a protected covered-outdoor location where it is sheltered from direct rain, snow and water exposure. A published IP weather rating is not listed.
Are wall screws and anchors included?
No. Mounting hardware must be selected according to the wall or structural surface and the installation requirements.
Need Help Planning the Speaker System?
Send AVTECK the room dimensions, ceiling height, speaker quantity, amplifier model, mounting locations and required music or paging level. We can help calculate the transformer load and recommend practical wall speaker placement for the commercial space.
